OPEN SOURCE HARDWARE MONITOR INSTALL
OPEN SOURCE HARDWARE MONITOR SERIAL

There are a variety of front-ends for sensors data. Minimum Four Activate Window Delay (tFAW) 30.000 ns

Minimum Read to Pre-charge CMD Delay (tRTP) 7.500 ns Minimum Write to Read CMD Delay (tWTR) 7.500 ns Minimum Active to Auto-Refresh Delay (tRC) 49.500 ns Minimum Row Active to Row Active Delay (tRRD) 7.500 ns Minimum Write Recovery time (tWR) 15.000 ns Supported CAS Latencies (tCL) 8T, 7T, 6T, 5T

OPEN SOURCE HARDWARE MONITOR SERIAL

# decode-dimms Memory Serial Presence Detect Decoderīy Philip Edelbrock, Christian Zuckschwerdt, Burkart Lingner,ĭecoding EEPROM: /sys/bus/i2c/drivers/eeprom/0-0050īanks x Rows x Columns x Bits 8 x 14 x 10 x 64 Once installed, load the eeprom kernel module.įinally, view memory information with decode-dimms.

OPEN SOURCE HARDWARE MONITOR INSTALL

To read the SPD timing values from memory modules, install the i2c-tools package. Reading SPD values from memory modules (optional) # echo jc42 0x19 > /sys/bus/i2c/devices/i2c-0/new_deviceĪfter that your ram sticks temperature will be visible on sensors command:Īdapter: SMBus PIIX4 adapter port 0 at 0b00 This process consists of writing module_name and address to smbus_path. After that you need to tell to module that which addresses are need to used.

So address of 0x18 and 0x19 are DIMMs temp sensors.Īfter found this info, to read temperatures of RAM sticks, we need jc42 kernel module loaded. In my system, there are 2 DIMMs available. RAM SPD's are start from address 0x50 and RAM temp sensors start from 0x18 at same bus. The i2cdetect command will show the devices that connected to the bus. In my system, RAM sticks connected to the bus is SMBus 0. I2c-0 unknown SMBus PIIX4 adapter port 0 at 0b00 N/A I2c-2 unknown SMBus PIIX4 adapter port 1 at 0b20 N/A I2c-2 unknown SMBus PIIX4 adapter port 2 at 0b00 N/A

Otherwise, its output will appear as follows: I2c-0 smbus SMBus PIIX4 adapter port 0 at 0b00 SMBus adapter I2c-2 smbus SMBus PIIX4 adapter port 1 at 0b20 SMBus adapter # i2cdetect -l i2c-2 smbus SMBus PIIX4 adapter port 2 at 0b00 SMBus adapter To show all the columns, use i2cdetect as root: Once installed, load the i2c-dev kernel module. To find the temperature sensors of DIMMs, install the i2c-tools package. 'In my …') and the language in some sentences can be improved for readability and compliance with Help:Style#Spelling and Help:Style#Language. In particular, section should avoid first person (i.e. Ln -s '/usr/lib/systemd/system/lm_rvice' '/etc/systemd/system//lm_rvice' * Chip `Intel digital thermal sensor' (confidence: 9)īusdriver `i2c_nforce2', I2C address 0x4cĬhip `Winbond W83L771AWG/ASG' (confidence: 6)ĭo you want to overwrite /etc/conf.d/lm_sensors? (YES/no): Now follows a summary of the probes I have just done. Some south bridges, CPUs or memory controllers contain embedded sensors.ĭo you want to scan for them? This is totally safe. It is generally safeĪnd recommended to accept the default answers to all questions, To load to use lm_sensors most effectively. # sensors-detect This program will help you determine which kernel modules you need When the detection is finished, a summary of the probes is presented. This will create the /etc/conf.d/lm_sensors configuration file which is used by lm_rvice to automatically load kernel modules on boot. The 'safe' answers are the defaults, so just hitting Enter to all the questions will generally not cause any problems. It will ask to probe for various hardware. See #Laptop screen issues after running sensors-detect. Warning: Do not use anything other than the default options (by just hitting Enter), unless you know exactly what you are doing.

Open source hardware monitor